공지 • Apr 09
Pantoro Gold Limited Provides Results from Ongoing Extensional and Infill Drilling Program At the Ok Underground Mine
Pantoro Gold Limited provided results from its ongoing extensional and infill drilling program at the OK Underground Mine as part of the Company's wider growth program.antoro commenced its growth drilling program at OK in late 2024, with activities scheduled to continue throughout the current year. The current program represents the first dedicated extensional drilling since the 2020 feasibility study. These new results continue to demonstrate strong continuity of both the O2 and Star of Erin Lodes, down-dip and along strike. Ongoing drilling will continue to focus on substantially increasing down-dip drill density to support further Ore Reserve upgrades. Information reported included size fraction weight, coarse and fine fraction gold content and calculated gold., Drilling techniques, Drill type (eg core, reverse circulation, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc) and details (eg core diameter, triple or standard tube, depth of diamond tails, face-sampling bit or other type, whether core is oriented and if so, by what method, etc). Underground diamond drilling is completed utilizing NQ2 (standard tube). Core is oriented routinely utilizing a Reflex Act3 orientation device., Historic Underground drilling was completed using electric hydraulic drill rigs with standard core LTK46 and LTK48 both with the same nominal core size of 38mm., Drill sample recovery, Method of recording and assessing core and chip sample recoveries and results assessed., Measures taken to maximise sample recovery and ensure representative nature of the samples., Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material., All holes were logged at site by an experienced geologist. Recovery and sample quality were visually observed and recorded., Diamond drilling practices result in high recovery in competent ground as part of the current drill program., No significant core loss has been noted in fresh material. The O2 and Main reefs are among the most nuggety at Norseman., Drill hole Information,: A summary of all information material to the understanding of the exploration results including a tabulation of the following information for all Material drill holes: easting and northing of the drill hole collar, - elevation or RL (Reduced Level - elevation above sea level in metres) of the drill hole collar, dip and azimuth of the hole, down hole length and interception depth, hole length., If the exclusion of this information is justified on the basis that the information is not Material and this exclusion does not detract from the understanding of the report, the Competent Person should clearly explain why this is the case. All holes with results available are reported., Criteria, JORC Code explanation, commentary, Data aggregation methods, In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum grade truncations (eg cutting of high grades) and cut-off grades are usually Material and should be stated., Where aggregate intercepts incorporate short lengths of high grade results, the procedure used for such aggregation should be stated and some typical examples of such aggregations should be shown in detail., The assumptions used for any reporting of metal equivalent values should be clearly stated., reported, reported drill results are uncut, All relevant intervals to the reported mineralised intercept are length weighted to determine the average grade for the reported intercept., No metal equivalents are reported., Relationship between mineralisation widths and intercept lengths, These relationships are particularly important in the reporting of Exploration Results., If the geometry of the mineralisation with respect to the drill hole angle is known, its nature should be reported., If it is not known and only the down hole lengths are reported, there should be a clear statement to this effect (eg 'down hole length, true width not known'). Drilling from the underground is drilled from static locations which means there are variable dips and azimuths due to access limitations, Downhole lengths are reported and true widths are calculated in both 3D using trigonometry and cartographic planes (section and plan view) using a formulae in excel, True widths are calculated and reported for drill intersections which intersect the lodes obliquely., Diagrams, Diagrams, Diagram's, Appropriate maps and sections (with scales) and sections (with scales) & sections (with scales) and tabulations of intercepts should be included for any significant discovery being reported. These should be included for any significant discover These should be included for anysignificant discovery being reported. These should been included, These should be included, These should be included in the report. These should be included, These may be included, These should be include, These should be included, these should be included, These should include, These should be included in any significant discovery being reported.